top of page

P0327 Code: Causes, Symptoms, Diagnosis & How to Fix It

Oct 31
6 min read
P0327 code knock sensor 1 circuit low input shown on an OBD2 diagnostic scanner

What Does P0327 Mean?

P0327 means “Knock Sensor 1 Circuit Low Input.” It is a generic OBD2 powertrain trouble code indicating that the PCM has detected a signal from knock sensor 1 that is lower than the expected range.


The knock sensor monitors engine vibrations associated with abnormal combustion, commonly called knock or detonation. The PCM uses the sensor signal to help adjust ignition timing and protect the engine.


P0327 does not automatically mean the knock sensor itself is defective. A low input signal can also result from damaged wiring, poor connections, incorrect sensor installation, electrical problems, or other circuit faults.


The exact sensor location, circuit design, and signal specifications vary by vehicle manufacturer.


P0327 Code Symptoms

Possible symptoms of P0327 include:

  • Check Engine Light

  • Reduced engine power

  • Poor acceleration

  • Engine hesitation

  • Poor fuel economy

  • Rough engine operation

  • Pinging or knocking under load

  • Reduced engine performance

  • Increased engine temperature in some conditions

Some vehicles may store P0327 with little or no noticeable change in drivability.


Common Causes of P0327

Several problems can cause the PCM to detect a low knock-sensor input.


1. Faulty Knock Sensor

A failing knock sensor may produce a signal that is weaker than expected.


2. Damaged Wiring

Broken, open, chafed, or shorted wiring can reduce or interrupt the signal reaching the PCM.


3. Poor Electrical Connection

Loose terminals, corrosion, bent pins, or water intrusion can create excessive resistance or an unreliable connection.


4. Incorrect Sensor Installation

Incorrect mounting or tightening can affect how the knock sensor detects engine vibrations.


5. Damaged Connector

A damaged connector may prevent the sensor from transmitting the correct signal.


6. Electrical Interference

Electrical noise or improperly routed wiring can interfere with the relatively low-level knock-sensor signal.


7. Sensor Ground or Reference Problem

Depending on the vehicle design, a problem with the sensor's circuit reference, ground, or associated wiring can result in a low signal.


8. Engine Mechanical Problems

Unusual engine vibrations or mechanical noise can affect knock-sensor operation and produce misleading diagnostic results.


9. PCM Problem

A PCM fault is possible but should generally be considered only after the sensor and circuit have been thoroughly tested.


How the Knock Sensor Works

The knock sensor detects vibrations generated by the engine.


During abnormal combustion, such as detonation, the engine can produce characteristic vibration patterns. The knock sensor converts these vibrations into an electrical signal that the PCM can evaluate.


The PCM uses this information to make ignition-timing adjustments when necessary.


With P0327, the PCM has determined that the input signal from knock sensor 1 is lower than expected.


This makes P0327 more specific than a general knock-sensor circuit malfunction, but it still does not prove that the sensor itself has failed.


P0327 vs P0325

P0325 means Knock Sensor 1 Circuit Malfunction.

P0325 is a general circuit malfunction code, while P0327 specifically indicates that the PCM is receiving a lower-than-expected input signal.


P0327 vs P0326

P0326 means Knock Sensor 1 Circuit Range/Performance.

P0326 indicates that the signal is outside the expected range or performance characteristics, while P0327 specifically identifies a low input condition.


How to Diagnose P0327

Always use the manufacturer's wiring diagrams, testing procedures, and specifications for the exact vehicle.


Step 1: Scan for All Trouble Codes

Use an OBD2 scanner to retrieve stored and pending codes.

Look for related:

  • Knock sensor codes

  • Misfire codes

  • Ignition codes

  • Fuel-system codes

  • Engine-temperature codes

  • Other powertrain codes

Record freeze-frame information before clearing the codes.


Step 2: Check Technical Service Bulletins

Search for technical service bulletins for the vehicle, engine, and model year.

Manufacturers may have documented issues involving knock sensors, wiring, connectors, or PCM software.


Step 3: Identify Knock Sensor 1

Use manufacturer service information to identify the location and wiring of knock sensor 1.

Sensor numbering can vary between engine designs, so do not assume its location.


Step 4: Inspect the Sensor

Check for:

  • Physical damage

  • Cracks

  • Corrosion

  • Oil contamination

  • Coolant contamination

  • Heat damage

  • Incorrect mounting

  • Signs of previous repairs

Confirm that the correct sensor is installed.


Step 5: Inspect the Wiring

Carefully inspect the entire circuit.

Look for:

  • Broken wires

  • Chafed insulation

  • Melted wiring

  • Open circuits

  • Short circuits

  • Poor previous repairs

  • Wiring contacting hot engine components

A damaged wire can produce a low signal even when the sensor is functioning correctly.


Step 6: Inspect the Connector

Check the connector for:

  • Corroded terminals

  • Loose pins

  • Bent terminals

  • Damaged locking tabs

  • Water intrusion

  • Poor terminal tension

Repair connector problems before replacing the sensor.


Step 7: Test the Circuit

Use the vehicle's wiring diagram and a DVOM to test the knock-sensor circuit.

Depending on the application, testing may include:

  • Continuity

  • Resistance

  • Signal voltage

  • Circuit voltage

  • Short-to-ground testing

  • Short-to-voltage testing

Compare all measurements with manufacturer specifications.

Do not use a universal knock-sensor voltage or resistance value because specifications vary between vehicles.


Step 8: Check Sensor Mounting

Verify that the knock sensor is installed in the correct position and tightened according to manufacturer specifications.

Incorrect mounting can prevent the sensor from detecting engine vibrations correctly.


Step 9: Check Live Data

If the vehicle provides knock-sensor or related data through the scan tool, monitor the available parameters.

Observe the signal under different engine conditions and compare the results with manufacturer specifications.


Step 10: Check for Electrical Interference

Inspect nearby wiring and ignition components for potential sources of electrical noise.

Make sure the knock-sensor wiring follows the manufacturer's intended routing.


Step 11: Check for Engine Problems

If the engine has unusual vibration, pinging, knocking, misfires, or poor performance, investigate the underlying mechanical or combustion condition.

Check relevant systems such as:

  • Fuel quality

  • Air-fuel mixture

  • Ignition timing

  • Engine temperature

  • Carbon buildup

  • Fuel-system operation


Step 12: Check the PCM

If the sensor and circuit test correctly, check for manufacturer-recommended PCM software updates or known module issues.

Do not replace the PCM without evidence that the module is actually defective.


Step 13: Clear and Retest

After completing the repair, clear the diagnostic codes.

Start the engine and perform an appropriate road test.

Confirm that P0327 does not return and that engine performance is normal.


How to Fix P0327

The correct repair depends on the confirmed cause.

Possible repairs include:

  • Replace a faulty knock sensor

  • Repair damaged wiring

  • Repair an open circuit

  • Repair a shorted circuit

  • Repair or replace damaged connector terminals

  • Correct poor electrical connections

  • Correct sensor mounting or torque

  • Repair electrical interference

  • Repair engine conditions causing abnormal vibration

  • Correct fuel or ignition problems

  • Update or reprogram the PCM when manufacturer information confirms a software issue

  • Replace the PCM only after proper testing confirms failure

Do not automatically replace the knock sensor simply because P0327 is stored.


Is P0327 Serious? Can You Drive With It?

P0327 should be diagnosed promptly because the knock sensor provides information that can help the PCM respond to abnormal combustion.


If the vehicle is actively knocking, overheating, misfiring, losing significant power, or running very poorly, avoid driving it until the problem is diagnosed.


If the vehicle has only a steady Check Engine Light and otherwise operates normally, a short trip to a repair facility may be possible.


However, extended driving with an unresolved knock-sensor problem is not recommended.


P0327 vs P0328

P0327 means Knock Sensor 1 Circuit Low Input.

P0328 means Knock Sensor 1 Circuit High Input.

The two codes identify opposite signal conditions: P0327 indicates a lower-than-expected input, while P0328 indicates a higher-than-expected input.


P0327 vs P0330

P0330 means Knock Sensor 2 Circuit Malfunction.

P0327 specifically involves knock sensor 1 and identifies a low input condition. P0330 identifies a general circuit malfunction involving knock sensor 2.

The exact sensor locations depend on the engine configuration.


Frequently Asked Questions


  1. What does P0327 mean?

    P0327 means Knock Sensor 1 Circuit Low Input. The PCM has detected a signal from knock sensor 1 that is lower than the expected range.

  2. Does P0327 mean the knock sensor is bad?

    No. A faulty sensor is only one possible cause. Wiring, connectors, mounting, electrical interference, and circuit problems can also cause P0327.

  3. Can P0327 cause loss of power?

    Yes. The vehicle may experience reduced performance or altered ignition timing when the PCM detects a knock-sensor problem. An underlying engine issue can also cause power loss.

  4. Can P0327 cause engine knocking?

    P0327 does not necessarily cause engine knock. However, if the PCM cannot reliably receive the knock sensor signal, it may have less accurate information about abnormal combustion.

  5. Can I drive with P0327?

    If the vehicle is knocking, overheating, misfiring, or experiencing major power loss, avoid driving it. If it operates normally with only a steady Check Engine Light, a short trip for diagnosis may be possible.

  6. Should I replace the knock sensor first?

    No. Inspect and test the sensor, wiring, connector, mounting, and circuit before replacing the sensor.

  7. Is P0327 the same as P0326?

    No. P0326 indicates Knock Sensor 1 Circuit Range/Performance, while P0327 specifically indicates Knock Sensor 1 Circuit Low Input.


bottom of page